November 2017 – Vertical Cuttings Dryer,Vertical Centrifuge, drilling waste management and treatment equipment,Oil based mud treatment system-KOSUN

11/21/201711/22/2017

Several Oily Sludge Management technologies

At present, the total amount of oily sludge produced in our country has exceeded 500 million tons every year, and the output also shows an increasing trend year by year. Oily sludge mainly from the following three aspects.( Oily Sludge Management)

(1) crude oil extraction process. Crude oil production process will produce a amount of oily sludge. The sludge produced mainly from the oil recovery wastewater treatment, the sedimentation caused by the added water purifying agent and the crude oil produced by drilling.

(2) Oil gathering process. Oil gathering process will produce a amount of oily sludge. Transfer stations and joint station tank sludge, sedimentation tank sediment, grease trap sediments are all oily sludge. Oil sands produced from natural gas purification plants and sludge are also oily sludge.

(3) Sewage treatment plant. Oil refinery wastewater treatment plant will also produce oily sludge, mainly from the biochemical pool of excess sludge, grease trap sediment, flotation tank scum, crude oil tank sediment.

Several Oily Sludge Management technologies

Oily sludge must be treated as it is detrimental to the environment. At present, there are several commonly used methods for the treatment of oily sludge in our country: incineration, thermal desorption, landfill, etc. In addition, there are biological treatment, coking and chemical heat washing.

In response to the requirement of resource-based, harmless and reduction of oily sludge treatment in our country, there are many new oily sludge treatment technologies emerging such as ultrasonic treatment of oily sludge technology, cement sludge co-treatment of oily sludge technology and Solvent extraction processing technology.

The source, composition, characteristics and nature of oily sludge in oilfields all over China are different, so the technology applied to oily sludge management is not the same. Therefore, the oil field in the selection of oily sludge treatment technology should be based on the advantages and disadvantages of various technologies and the scope of application. Combined with their own circumstances choose a reasonable technology.(Editor:Kosun Lily.Wang)

Kosun- China Solids Control Leader&Drilling Waste Management Expert

Tel.: +86 29 87304914

Email: sales2@adkosun.com

Contact person: Lily Wang

Online consulting:

http://www.kosun.com

http://www.kosuneco.com

11/17/2017

Oil Drilling Waste Management Company and equipment

With the continuous improvement of environmental protection requirements, the major oil fields are faced with the problem of oil drilling waste management. KOSUN, Oil Drilling Waste Management Company, are searching drilling waste management and disposal methods for 25 years, manufacturing quality drilling cuttings waste management system and serving the clients around the world.

Oil Drilling Waste Management equipment- Vertical Cuttings Dryer:

KOSUN vertical cuttings dryer for oil-based mud, by centrifugal separation principle, can effectively recover the cuttings in liquid phase composition, the solid phase becomes very dry, the drilling mud in the recovery, reduce the cost of drilling operation, but also reduces the the pollution of the environment, in accordance with international emission standards and environmental protection requirements. It can be used for drilling cuttings in land and ocean drilling.

Oil Drilling Waste Management equipment- Decanter Centrifuge:

KOSUN DC Series Decanter Centrifuge is used to separate suspended solids ≥2μm in diameter and treat the drilling mud and fluids. It is especially effective when used in oilfield service industry, industrial service industry and especially in environmentally sensitive areas. This type of centrifuge is high in recovery rate, effective in solids control and remarkable in the reduction of cost spent on drilling mud resupplying and management. It is a very sophisticated dynamic balancing machine, able to operate stably with the whirling speed ranging from 0 to 3900 and generate centrifugal force of 3000G.

KOSUN Decanter Centrifuge can meet with different requirements of mud treatment under various drilling conditions, that can do sedimentation and separation for particles more than 2 μm. After treatment, the mud can achieve ideal viscosity and proportion, resulting in better recycling, high efficiency, saving and environment protection.

The series of centrifuge by our company has been developed many years with the continuous improvement and optimization design, which possesses the characteristics of good result of separation and settlement, as well as large quantity, reliable work, longer life, lower energy consumption, easy maintenance, smooth operation, lower noises, etc. (Editor:Kosun Lily.Wang)

Kosun- China Solids Control Leader&Drilling Waste Management Expert

Tel.: +86 29 87304914

Email: sales2@adkosun.com

Contact person: Lily Wang

Online consulting:

http://www.kosun.com

http://www.kosuneco.com

11/16/2017

Prospects for Oil Sludge Management

With the promulgation of the new Environmental Law, the environmental requirements are getting higher and higher for oil fields, and free discharge of oil sludge will not be allowed any more. Oil Sludge Management is becoming a focal issue.

oil sludge management

Oil sludge is oil mixed with soil. They will be mixed together and become very difficult to deal with. Oil sludge is mainly from two aspects: Firstly, crude oil from the stratum to the ground and accumulated in all kinds of containers, large tanks and recycling pools and other ground facilities; secondly, oil sludge produced by oil well operations.

Oily sludge is mainly derived from oil field mining and sewage treatment plants. In general, the sludge oil content is from 10% to 50%, and moisture content is from 40% to 90%. The ultimate purpose of oil sludge management is to reduce the harmful resources. The common oil sludge treatment methods are solvent extraction, incineration, biological, coking, oily sludge profile control, and comprehensive utilization of oil sludge. The results show that the current methods for oil sludge management have their own characteristics and scopes of application. As the oil sludge composition is so complex, there is no treatment method that can treat all types of oily sludge.

According to statistics, the pollutant treatment market size is about CNY100~150 billion each year, and according to a rough calculation, the investment in oil sludge management plant needs more than CNY150 billion.

Since 2007, Daqing Oilfield have built nine oil sludge management stations, and the annual treatment capacity can reach 3.2 million tons, all the oil sludge had been treated harmlessly. Changqing Oilfield built a Longdong oil field sludge treatment station in 2013 and used the physically and chemically combined methods, the oil content of the treated oil sludge is less than 2%, and moisture content is less than 60%, while the crude oil can be recovered. Xinjiang Fengcheng Oilfield Work Zone uses microbial agents to deal with heavy oil sludge and sludge oil content is reduced from 15% down to below 2% after treatment, which is very good. The current test has been reviewed by the company.

KOSUN can provide a corresponding set of oil sludge management plant, and our products have been exported to foreign countries, such as the United States, Europe, Russia, the Middle East and other regions, and our oil sludge treatment systems are well received by the foreign customers. If you need more information about our oil sludge management plant, please feel free to contact us! (Editor:Kosun Lily.Wang)

Kosun- China Solids Control Leader&Drilling Waste Management Expert

Tel.: +86 29 87304914

Email: sales2@adkosun.com

Contact person: Lily Wang

Online consulting:

http://www.kosun.com

http://www.kosuneco.com

11/14/2017

Oil Sludge Treatment Plant

Oil Sludge Treatment Plant (equipment) :

–Shale Shaker for coarse solids separation

–Decanter Centrifuge for fine solids separation or water and oil separation.

-Oil Water separators for two phase liquid separation.

-Thermal desorption unit for minimize the oil on the solids down to 0.3%.

The oil sludge is the waste of solid with oil from oil drilling, transportation, refinery and oil waste water treatment processing. It contains big quantity benzene series, phenols, anthracene, pyrene and other harmful rotten material. It will be a resource waste and pollution for environment.

Oil sludge origin:

Crude oil drilling work
Rig site waste during gathering and transportation
Waste water treatment plant in refinery plant

Different areas and different clients has different oily sludge and final requirements for the oily sludge separation & treatment, following questions are needed to be clear for us to provide the best proposal for your oily sludge treatment solutions.

-What is the origin and geographic location of the waste sludge (drilling, refinery, other)?

-What is the makeup of the oil sludge (percentage of oil, water and solids)?

-What volume of oil sludge is to be treated?

-How long you need to complete the treatment of the oil sludge?

-What is the challenge or problem of the current situation?

-What is the target to achieve for the final oil, water and solids?

-What process / equipment is being used on location at present for the oil sludge treatment? How is the performance now?

-What’s your budget for the oil sludge treatment plant?

Knowning above queations,we can supply you suitable Oil Sludge Treatment Plant ! (Editor:Kosun Lily.Wang)

Kosun- China Solids Control Leader&Drilling Waste Management Expert

Tel.: +86 29 87304914

Email: sales2@adkosun.com

Contact person: Lily Wang

Online consulting:

http://www.kosun.com

http://www.kosuneco.com

11/06/201711/08/2017

Infrastructure project mud management and Separation

With the development of the city, most of the old buildings were dismantled. After the demolition of old buildings, the construction mud or infrastructure project mud generated by construction waste problem is difficult to solve. If untreated construction mud is poured directly into farmland, the acid-base balance of the soil will be destroyed, leaving the land unable to be cultivated; if discharged into rivers, it will result in serious water pollution. How to deal with the construction mud or infrastructure project mud?( Infrastructure project mud management and Separation)

In the experiment of mud treatment, it is found that the construction rubbish such as concrete, brick, slag and so on has the value of reuse.They can be used as backfill earthwork, and part of topsoil can also be used for garden planting. How to solve the construction mud treatment problems? With the acceleration of the urbanization process, a large number of projects are under construction every year in the urban area, and the construction mud generated by the construction is also increasing substantially. Due to many origins, many management links and many main responsibilities, construction mud often can not be properly disposed, seriously affecting the river water quality and water environment.

There are three characteristics of construction mud or infrastructure project mud: ① large amount of mud production: Once the construction machinery started, it can produce a lot of mud in a short period of time; ② storage difficulties: the scene does not have a large volume mud pool, direct emissions can pollute the environment, cars transport costs are high, on-site processing is the best solution.

As technology continues to evolve, there are traditional sedimentation tanks for mud treatment or mechanical treatment. Sedimentation tank has a larger investment. The use of mechanical methods need to invest a certain amount of funds to purchase equipment, common mud treatment equipment, including mud dewatering shale shaker, desander, centrifuge, and the treatment effect is relatively good.

KOSUN mud management equipment is the best choice for construction mud or infrastructure project mud treatment with the advantages of small footprint, easy to transport, high degree of automation and control, energy saving and emission reduction! (Editor:Kosun Lily.Wang)

Kosun- China Solids Control Leader&Drilling Waste Management Expert

Tel.: +86 29 87304914

Email: sales2@adkosun.com

Contact person: Lily Wang

Online consulting:

http://www.kosun.com

http://www.kosuneco.com